Wallpaper is posted at the moment, absolutely more with half the effort

There are many home renovation procedures and several details. It is understood that wallpaper construction may be the last process of hard decoration of the house decoration, the beginning of soft decoration. Wallpapers should be completed in all hardware such as woodworking, paint, water and energy, plastering, and after a sanitary cleaning.

Floor and skirting are installed
❖ Avoid smashing the keel, sawing real wood, etc. when laying the floor to make the wallpaper dirty.
❖ Avoid vibration when installing the baseboard, which in turn causes the wallpaper to separate from the wall surface area, leading to bubbling and curling of the wallpaper.
❖ Avoid a lot of dust pollution and bruises when slicing the baseboard.
❖General putty will not be approved at the bottom of the wall, the 1st wallpaper can’t be cut neatly, long time is prone to curling, causing the wallpaper to roll up.
❖ Avoid kicking the skirting range by sealing the wallpaper with cup glue, so that the drinking water molecules in the wall structure can’t be discharged, resulting in mildew of the baseboard.
After the kicking line is installed, it’s possible that the wall and the skirting line are not flat plenty of or have a gap. The post-installed wallpaper has the effect of within the gap.

Door cover and door are installed
First install the entranceway in order to avoid the wallpaper from being damaged and filthy, in fact it is also simple to repair the color. If the wallpaper is patched and the paint is definitely repaired (the gap between your door cover and the wall structure and the gap between the skirting lines) will stain the wallpaper.
How big is the card may vary. If the size is certainly too small, the wallpaper will end up being attached initial, and a blank will appear after the door is installed. If it’s full, it will quickly draw the wallpaper when the entranceway is installed, causing harm to the wallpaper.

Wood lacquer finish can’t be wallpapered first, then solid wood lacquer
❖Because the real wood lacquer is sprayed during construction, the paint will adhere to the wallpaper. And when the paint can be applied, the completed product should be secured. In particular, the encompassing wall of the cabinet, door, partition, etc. ought to be covered with a protective film. If it’s atomized to the wall structure surface, the building quality of the wallpaper isn’t guaranteed, in fact it is simple to cause problems.

Air-con hole is well
❖ Avoid punching and damage the wallpaper.
❖ Avoid wall structure vibration when punching, leading to the wallpaper to fall off.
❖ Avoid dusting the wallpaper when punching.
Curtain rod hole is pre-made
The position of the curtain hanging rod support is well designed, and the hole was created to avoid the hole punching the surface of the wallpaper. Especially for flocking, silk, deep embossing, special materials and various other hard-to-care wallpapers, make sure to pre-attract the curtain rod holes before pasting.

How to paste wallpaper?
Remove the wall skin: take away the original color and various other objects on the wall structure, make use of gypsum powder to fill up the cracked section of the wall structure, and put a bandage after flattening; if it is sand gray wall, partition wall, it should be covered with cup cloth Or indeed great cloth; some poor quality partitions or external walls to reach the insulation effect, have to be filled with plasterboard

Slice the wallpaper: first measure the height of the wall structure, then cut the length of the wallpaper, right now there are two kinds of cases: no flower wallpaper based on the elevation of the wall structure is cut about 5 to 8 cm duration, as the upper and lower trimming: the flower wallpaper must consider the design symmetry Sex, therefore the length of the cut ought to be increased based on the actual situation, generally 8 to 10 cm longer.

Applying glue: Apply the wallpaper glue to the trunk of the cut wallpaper with a brush, pay special attention to the encompassing edges to be coated with glue to guarantee the building quality, the painted wallpaper, and the glue to face the fold. 5- ten minutes (3D Wall covering remember that no external pressure should be put on prevent creases in the wallpaper, especially the cloth). After the glue is totally penetrated into the paper, it could be posted, and many wallpapers are applied each time and posted in order. Special material wallpaper must be glued on the wall structure, such as for example velvet sound-absorbing wallpaper, gold foil tin wallpaper, etc.

Wallpaper structure: Generally, the initial wallpaper is posted from the very best to the bottom of the entranceway or the part of the corner. Utilize the squeegee from top to bottom, from the inside to the outside, lightly scrape the wallpaper, squeeze out the bubbles and excess glue to help make the wallpaper smooth. Close to the wall.

Wallpaper building: Generally, the initial wallpaper is posted from the top to underneath of the door or the corner of the corner. Utilize the squeegee throughout, from the inside to the outside, softly scrape the wallpaper, squeeze out the bubbles and excess glue to make the wallpaper smooth. Near to the wall.

Before wallpapering, turn off the power: When wallpapering, in case you have a power switch or socket on the wall, you can turn off the main power supply, then cover the wallpaper with all the current power and socket, and cut two pairs from the guts of gravity. The corner range will show four little triangles, and then utilize the utility knife to remove the extra wallpaper around.

Trimming and cleaning: Cut off the excess wallpaper at the top and decrease ends. The advantage of the knife should be sharp to avoid burrs. When cutting some wall coverings, it is advisable to use a Japanese imported blade with a price of 1 1.5 yuan. Then use a sponge dampened with water to completely wipe the glue staying on the top of wallpaper to prevent the wallpaper from turning yellowish. If the wallpaper is certainly dry following the wallpaper is dry, make use of a knife to cut the injected glue and flatten it to get rid of it. it is good)